This is an old revision of the document!
Discovar de novo is a next generation sequence assembly program. The program was developed by the Broad Institute and was released late in 2014. Discovar de novo is designed for 250 bp long illumina reads with the PCR duplicates and adaptor sequences removed. The following webpage contains the manual as provided by the Broad Institute (http://www.broadinstitute.org/software/discovar/blog/):
The raw data was received as fastq pairs. Each pair contains a forward and reverse strand. These pairs are ran through Skewer to remove adaptor sequences, then ran through fastUniq to remove PCR duplicates. Next the forward and reverse strand are merged into a single unaligned BAM file.
All unaligned BAM files are then passed into Discovar de novo. The output is an assembly in .fasta format and Discovar de novo visualization files. The .fasta file can then be re-scaffolded with a scaffolding program (see next workflow). The finished file can be represented on the UCSC genome browser.
Discovar de novo currently does not support mate pair libraries. To incorporate these data the program a program SSpace was used to re-scaffold the Discovar de novo fasta output. The workflow below describes how mate pair libraries are processed and factored into the assembly. The SSpace library is a small text file that points to the libraries and provided meta data statistics. Please see the 'Programs used' section for SSpace citation and further details.
After removing adapters and PCR duplicates, we run FastQC in two of the libraries. In general, the quality of the reads decrease in the last base-positions. Also, read 2 of the SW019 library shows problems in the per tile sequence quality. Bellow are the pdf files with the fastqc for the PCR and adapter removed libraries. The protocol we used to run fastqc is uploaded in this link: fastqc. The path to the files is: campusdata/gchaves/fastqc_trimmed_PCR_duplicates.
The fastq to bam conversion was performed using the picard toolset. Specifically the fastqToSam.jar file was used to prepare the bam files.
Discovar de novo was designed for very specific data. To test the validity of our data we perform different test runs. The test runs used a percentage of data from the libraries available. All the tests were run on .bam files. The log files were run on edser2 or campusrocks nodes with more than 200 GB of RAM available. The run logs are stored as .txt files. The full logs can be seen on the wiki here,
|Run log||Data used|
|1% data||(Pre Skewer and FastUniq) MiSeq data SW019_S1_L001, HiSeq data SW018_S1_L007, HiSeq data SW019_S2_L008|
|5% data||(Pre Skewer and FastUniq) MiSeq data SW019_S1_L001, HiSeq data SW018_S1_L007, HiSeq data SW019_S2_L008|
|10% data||(Pre Skewer and FastUniq) MiSeq data SW019_S1_L001, HiSeq data SW018_S1_L007, HiSeq data SW019_S2_L008|
|50% data||(Post Skewer and FastUniq) MiSeq data SW019_S1_L001, HiSeq data SW018_S1_L007, HiSeq data SW019_S2_L008|
|50% data UCSF||(Post Skewer and FastUniq) UCSF SW018 and SW019 data|
The logs are very large, important statistics have been gathered and are compared below. Note that MPL1 is an acronym for mean length of first read in pair up to first error.
|1% run||5% run||10 % run||50 % run||50% UCSF run|
|Total runtime||1.75 hours||1.53 hours||2.4 hours||8.53 hours||14.9 hours|
|Peak memory use||43.92 GB||78.10 GB||151.05 GB||220.11 GB||184.09 GB|
|Bases in 1kb+ scaffolds||75,233||592,685||1,476,875||101,397,871||1,528,625,509|
|Bases in 10kb+ scaffolds||10,572||11,088||168,543||151,417||137,959,107|
Our fasta assembly files are located at
Each fasta assembly is in its own directory, the directory name is the assembly name. Currently there are five assemblies, The final fasta file is name a.lines.fasta. Note originally the authors used the a.fasta file (which contains the reverse complement of every contig) for statistics. Consequently statistics were falsely reported as twice the actual number until May 15th 2015 when the error was identified. The statistics have since been corrected.
Raw stats were mined from the fasta files using a python script fastaStats.py. The script is available online at (https://github.com/ChrisEisenhart/binfProgs/blob/master/basicProgs/fastaStats.py).
NOTE for all statistics listed below the scaffolds and contigs are identical
|Assembly name||Bytes||Total bases||# scafs||Av. scaf len||Longest scaf||Scaf N50||# Scaf > 5Kb||Bases in 10kb+ scafs|
Looking at the 10% run, the majority of scaffolds generated are quite short (<1kb).
When a similar histogram is generated for the assembly made with 50% of the SW018 and SW019 reads from UCSF, you can see that the average scaffold length is higher and there are quite a few more scaffolds that are over 10kb.
The banana slug genome is estimated to be 2.1 billion bases (2,800 million), our latest run has assembled just under 2 billion bases!
The program SSPace (documentation below) was used to scaffold the the assembly with mate pair data. The UCSF SW041 and SW042 mate pair libraries were used to generate the library.txt file.
The .fasta assemblies were run through BLAST. The results are below,
There seems to be a very high sequence identity with Notopygos (http://sv.wikipedia.org/wiki/Notopygos)
See instructions for setting up the hub here, Banana slug browser
The program, its location, and a brief, (brief!) explanation of what the program does
The Picard is a set of Java-based command-line utilities for SAM and BAM file manipulation (edser2:/soe/calef/picardtools and edser2:/soe/calef/picard_jars). Webpage: http://picard.sourceforge.net/.
Is a general purpose malloc(3) implementation that emphasizes fragmentation avoidance and scalable concurrency support (edser2:/soe/calef/jemalloc). Webpage: http://www.canonware.com/jemalloc/.
Skewer is an adapter trimmer for Illumina paired-end sequences (/campusdata/BME235/S15_assemblies/SOAPdenovo2/adapterRemovalTask/skewer_run). Webpage: http://sourceforge.net/projects/skewer/.
FastUniq is a fast de novo duplicate removal tool for paired short DNA sequences (/campusdata/BME235/bin). Webpage: http://sourceforge.net/projects/fastuniq/.
GCC is a compiler for the GNU operating system. Webpage: https://gcc.gnu.org/.
A program for scaffolding fasta files, written by Marten Boetzer and Walter Pirovano. The authors are very protective over the use and citation of this program. The program can be obtained by at http://www.baseclear.com/genomics/bioinformatics/basetools/SSPACE.
Boetzer M, Henkel CV, Jansen HJ, Butler D, Pirovano W(2011), Scaffolding pre-assembled contigs using SSPACE, Bioinformatics 27(4):578-9
blog posts, related information etc.